Bevelled steel ruler with one millimetre graduation.Ground on all faces. Etched, precision graduation, easy to read and long-lasting. Serial number.Manufactured as per DIN 866/1.
ART.0381 - PRECISION STRAIGHT EDGE IN STAINLESS STEEL
Temperatured stainless steel control ruler.
Suitable for high precision checks.
Rectified on all sides.
With handle and section for << I >> for stability and lightness.
Equipped with serial number.
Built according to DIN 874/1 standard.
Size chart
Women's clothing size
| Size | XS | S | M | L |
|---|---|---|---|---|
| Euro | 32/34 | 36 | 38 | 40 |
| USA | 0/2 | 4 | 6 | 8 |
| Bust(in) | 31-32 | 33 | 34 | 36 |
| Bust(cm) | 80.5-82.5 | 84.5 | 87 | 92 |
| Waist(in) | 24-25 | 26 | 27 | 29 |
| Waist(cm) | 62.5-64.5 | 66.5 | 69 | 74 |
| Hips(in) | 34-35 | 36 | 37 | 39 |
| Hips(cm) | 87.5-89.5 | 91.5 | 94 | 99 |
How To Measure Your Bust
With your arms relaxed at your sides, measure around the fullest part of your chest.
How To Measure Your Waist
Measure around the narrowest part of your natural waist, generally around the belly button. To ensure a comfortable fit, keep one finger between the measuring tape and your body.
Reference:
ART.0381
Love0
Add to compare0
20 other products in the same category:
Onglet square in non-deformable steel.With anti-corrosion treatment.This square is equipped with several degrees: in fact, it is possible to measure 90° - 45° - 30° - 120°.Fully ground on the surfaces.Built according...
Black granite inspection square, suitable for perpendicularity checks.Highly reliable instrument, thanks to very narrow tolerances and support stability.Lightning holes are drilled on the large squares.The surfaces...
Flexible rulers in material stainless steel.Division on one side only, etched, easy to read and long-lasting.Manufactured as per DIN 866/2.Particular divisions and numberings available upon requirement.
Tempered stainless steel cap square.Completely ground on the faces.High precision as it is made and tested according to restricted procedures.Equipped with serial number.Built according to DIN 875/0 standard.Supplied...
Simple steel square with anti-corrosion galvanic treatment.Being machined from solid, it allows for two 45° angles and one 90°.Entirely ground surfaces.
Flat 135° square in non-deformable steel. Entirely ground surfaces. Manufactured as per DIN 875/2.
High precision square in hardened stainless steel.Complete with adjustable rule.In cobalt super-fast steel, ground and HRC hardened 64÷ 65.Provided with angle reading indicator in degrees from –10° / 0° /...
Simple 120° square in non-deformable steel.Completely ground on the surfaces.Built according to DIN 875/2 standard.
PDF TAB
Simple square in hardened stainless steel.Completely ground on the faces.High precision as it is made and tested according to restricted procedures.Equipped with serial number.Built according to DIN 875/0...
High precision square in hardened stainless steel.Complete with adjustable round rule.In 64÷ hardened cobalt super-rapid steel 65 HRC.Suitable for matrix corrector.Manufactured according to DIN 875/0 standard.Supplied...
High precision square in hardened stainless steel.Complete with 45º bevelled edge beam in super-rapid cobalt steel.Ground and hardened to HRC 64-65.Suitable for a mould checker.Manufactured as per DIN 875/0.Supplied...
Square with non-deformable steel hat.The reduced section makes it more manageable and suitable for blacksmiths and carpenters.Entirely ground on the faces and protected by an anti-corrosion treatment. Built with...
Ruler in non-deformable steel with one millimetre graduation.Ground on all faces.Etched, precision graduation, easy to read and long-lasting.Serial number.Manufactured as per DIN 866/1.
Simple square in non-deformable chromed steel.The square is covered with a uniform layer of hard chrome applied with a special procedure which ensures a high degree of hardness and protection to the surfaces from...
Parallel block in stabilized G26 pearlitic cast iron.Fine planed working surface.
Millimeter control line in non-deformable steel.Rectified on all faces.Engraved precision graduation, easy to read, durable over time.Equipped serial number.Built according to DIN 874/1 and DIN 866/1 standards.
PDF TAB
Periphery tape small section in steel for round bodies.The instrument has two scales: the upper one is for diameters and the lower for circumferences.
45° square with stock in non-deformable steel.Entirely ground surfaces.Manufactured as per DIN 875/2.
Cube for radial drills in stabilized G26 pearlitic cast iron.Properly ribbed to ensure strength.Fine planed working surface with “T” grooves.
English
Italiano 
