Parallel square in non-deformable steel with anti-corrosion treatment.The stop is hardened to reduce wear to the minimum.The entire beam is graduated in millimeters with long-lasting incision.A reference line is...
ART.0458 - SQUARE WITH BEAM Ø 3 MM
High precision square in hardened stainless steel.
Complete with adjustable round rule.
In 64÷ hardened cobalt super-rapid steel 65 HRC.
Suitable for matrix corrector.
Manufactured according to DIN 875/0 standard.
Supplied in case.
Size chart
Women's clothing size
| Size | XS | S | M | L |
|---|---|---|---|---|
| Euro | 32/34 | 36 | 38 | 40 |
| USA | 0/2 | 4 | 6 | 8 |
| Bust(in) | 31-32 | 33 | 34 | 36 |
| Bust(cm) | 80.5-82.5 | 84.5 | 87 | 92 |
| Waist(in) | 24-25 | 26 | 27 | 29 |
| Waist(cm) | 62.5-64.5 | 66.5 | 69 | 74 |
| Hips(in) | 34-35 | 36 | 37 | 39 |
| Hips(cm) | 87.5-89.5 | 91.5 | 94 | 99 |
How To Measure Your Bust
With your arms relaxed at your sides, measure around the fullest part of your chest.
How To Measure Your Waist
Measure around the narrowest part of your natural waist, generally around the belly button. To ensure a comfortable fit, keep one finger between the measuring tape and your body.
Reference:
ART.0458
Love0
Add to compare0
20 other products in the same category:
Square with non-deformable steel hat.The reduced section makes it more manageable and suitable for blacksmiths and carpenters.Entirely ground on the faces and protected by an anti-corrosion treatment. Built with...
Bait Guardapiano at 5 blades. Suitable for corrector matrices . in stainless steel, rectified and lapping. built According to DIN 874/0. provided in the case.
PDF TAB
Steel ruler with one millimetre graduation.Ground on all faces.Etched, precision graduation, easy to read and long-lasting.Serial number.Manufactured as per DIN 866/1.Cod. 10 total length 1000 mm as master of length.
Rulers with contraction in mat stainless steel.Division on one side, etched, easy to read and long-lasting.Contractions: 0,5% - 0,8% - 1,25% - 1,5% - 1,7% - 1.75% - 1,8% - 2% - 2,25% - 3% - 4% - 6%.Please specify the...
Flexible rulers in mat stainless steel. Division on one side only, etched, easy to read and long-lasting. Manufactured as per DIN 866/2. Particular divisions and numberings available upon requirement.
Simple set square in non-hardened stainless steel.Fully ground on the faces.High precision as it is made and tested according to restricted procedures.Equipped with a number of serial number.Built according to DIN...
Ruler in non-deformable steel with one millimetre graduation.Ground on all faces.Etched, precision graduation, easy to read and long-lasting.Serial number.Manufactured as per DIN 866/1.
team of high precision in stainless steel. Complete with square row with 45 ° chamtoe in super-rapid cobalt steel.Rectified and timing HRC 64 ÷ 65. Suitable for matrici corrector.Built according to DIN 875/0...
Square with stock in non-deformable steel.Entirely ground faces.High precision.Made to strict tolerances.Manufactured as per DIN 875/1.
Item 421 manufactured as per DIN 875/2.
High precision square in hardened stainless steel.Complete with adjustable rule.In cobalt super-fast steel, ground and HRC hardened 64÷ 65.Provided with angle reading indicator in degrees from –10° / 0° /...
Simple square in non-deformable steel.Completely ground on the faces.High precision being performed with tight tolerances.Built according to DIN 875/1 standard.
Art. 420 built according to the DIN 875/2 standard.
PDF TAB
Precision straight edge in non-deformable steel made to very small tolerances; for precision control situations.Ground on all faces.Serial number.Manufactured as per DIN 874/1.
G25 pearlitic cast iron square.Compact and stabilized structure.Fine planed work surfaces.
PDF TAB
Bevelled square with hardened stainless steel cap.The two chamfered and lapped sides allow for a more accurate visual check.The square is entirely ground. High precision as it is manufactured and tested according to...
Black granite inspection square, suitable for perpendicularity checks.Highly reliable instrument, thanks to very narrow tolerances and support stability.Lightning holes are drilled on the large squares.The surfaces...
Tempered stainless steel cap square.Completely ground on the faces.High precision as it is made and tested according to restricted procedures.Equipped with serial number.Built according to DIN 875/0 standard.Supplied...
Flat 135° square in non-deformable steel. Entirely ground surfaces. Manufactured as per DIN 875/2.
Simple square in non-deformable steel.The reduced section makes it more manageable and suitable for blacksmiths and carpenters.Entirely ground on the faces and protected by an anti-corrosion treatment.< br...
English
Italiano 
