Simple steel square with anti-corrosion galvanic treatment.Being machined from solid, it allows for two 45° angles and one 90°.Entirely ground surfaces.
ART.0425 - SQUARE IN NON-DEFORMABLE CHROMED STEEEL
Simple square in non-deformable chromed steel.
The square is covered with a uniform layer of hard chrome applied with a special procedure which ensures a high degree of hardness and protection to the surfaces from oxidation.
Entirely ground on the faces.
High precision being performed with tight tolerances.
Built according to DIN 875/1 standard.
Size chart
Women's clothing size
| Size | XS | S | M | L |
|---|---|---|---|---|
| Euro | 32/34 | 36 | 38 | 40 |
| USA | 0/2 | 4 | 6 | 8 |
| Bust(in) | 31-32 | 33 | 34 | 36 |
| Bust(cm) | 80.5-82.5 | 84.5 | 87 | 92 |
| Waist(in) | 24-25 | 26 | 27 | 29 |
| Waist(cm) | 62.5-64.5 | 66.5 | 69 | 74 |
| Hips(in) | 34-35 | 36 | 37 | 39 |
| Hips(cm) | 87.5-89.5 | 91.5 | 94 | 99 |
How To Measure Your Bust
With your arms relaxed at your sides, measure around the fullest part of your chest.
How To Measure Your Waist
Measure around the narrowest part of your natural waist, generally around the belly button. To ensure a comfortable fit, keep one finger between the measuring tape and your body.
Reference:
ART.0425
Love0
Add to compare0
20 other products in the same category:
Rulers with contraction in mat stainless steel.Division on one side, etched, easy to read and long-lasting.Contractions: 0,5% - 0,8% - 1,25% - 1,5% - 1,7% - 1.75% - 1,8% - 2% - 2,25% - 3% - 4% - 6%.Please specify the...
Precision straight edge in non-deformable steel made to very small tolerances; for precision control situations.Ground on all faces.Serial number.Manufactured as per DIN 874/1.
Semi-rigid rulers in mat stainless steel.Division on one side only, etched, easy to read and long-lasting.Manufactured as per DIN 866/2.Particular divisions and numberings available upon requirement.
Square with 120° cap in non-deformable steel.Completely ground on the surfaces.Built according to DIN 875/2 standard.
PDF TAB
Square with 135° cap in non-deformable steel.Completely ground on the surfaces.Built according to DIN 875/2 standard.
PDF TAB
Square with stock in non-deformable steel.Entirely ground faces.High precision.Made to strict tolerances.Manufactured as per DIN 875/1.
Item 421 manufactured as per DIN 875/2.
Square with striker and bevel in hardened stainless steel.The two chamfered and lapped sides allow for a more accurate visual check.Entirely ground, of high precision being performed and tested according to restricted...
Steel ruler with one millimetre graduation.Ground on all faces.Etched, precision graduation, easy to read and long-lasting.Serial number.Manufactured as per DIN 866/1.Cod. 10 total length 1000 mm as master of length.
Square with non-deformable steel cap.The base made from a single piece and not applied, makes this square very sturdy and suitable for heavy carpentry work.A galvanic treatment protects it from possible oxidation.
PDF...
Black granite inspection square, suitable for perpendicularity checks.Highly reliable instrument, thanks to very narrow tolerances and support stability.Lightning holes are drilled on the large squares.The surfaces...
high precision team in stainless steel timing. Complete with square row with 45 ° chamtoe in super-rapid cobalt steel. 65. Suitable for matrici corrector . built according to DIN 875/0. supplied in the case....
Flexible rulers in mat stainless steel. Division on one side only, etched, easy to read and long-lasting. Manufactured as per DIN 866/2. Particular divisions and numberings available upon requirement.
Hardened stainless steel knife-edge straight edge for fast and precise control of planarity and parallelism.Made from hardened stainless steel, ground with lapped contact angle.Fitted with heat-insulated...
Bait Guardapiano at 5 blades. Suitable for corrector matrices . in stainless steel, rectified and lapping. built According to DIN 874/0. provided in the case.
PDF TAB
45° square with stock in non-deformable steel.Entirely ground surfaces.Manufactured as per DIN 875/2.
Ruler in non-deformable steel with one millimetre graduation.Ground on all faces.Etched, precision graduation, easy to read and long-lasting.Serial number.Manufactured as per DIN 866/1.
Sliding square in non-deformable steel with anti-corrosion treatment.Suitable for the transfer of angles.
Flexible rulers in material stainless steel.Division on one side only, etched, easy to read and long-lasting.Manufactured as per DIN 866/2.Particular divisions and numberings available upon requirement.
Assembly box with T-grooves and slots.Made in G25 stabilised perlitic cast iron.Squareness between the scraped faces to DIN 875/3 precision.T-grooves and slots as per UNI 4788.
English
Italiano 
